An efficient method of generating vortex electromagnetic wave based on double‐layer transmissive metasurface

A broadband double‐layer transmissive metasurface (TMS) for effective generate vortex electromagnetic wave is presented in this paper. The proposed TMS consists of two types of elements. The first element is composed of a multi‐resonant dipole and four metal vias. The metal vias increase the coupling strength between the upper and lower layers to improve transmission efficiency. On the basis of the first element, the second element adds stubs to ensure sufficient phase shift. The far‐field cross polarisation is eliminated by special element arrangement. Then, a centre‐fed linear polarisation TMS is designed to generate orbital angular momentum beams with mode l = ? 1. The proposed TMS is designed, manufactured and measured to verify the proposed design. The measured results indicate that a maximum gain of 20.8 dBi and narrow divergence angle of ±5° are achieved at 18 GHz. Furthermore, mode purity is higher than 86.1% within the 17 to 19 GHz band. The proposed double‐layer TMS saved costs, reduced weight and without assembly error is a good candidate for OAM generator.     

In-fibre LP11–LP21 mode conversion using force-induced long-period fibre gratings with polarization controllers

ABSTRACT

Mode conversion between higher-order modes is attained in a step-index four mode fibre using an in-line polarization controller followed by a force-induced long period fibre grating. By adjusting the field orientation of the LP₁₁ mode to the antisymmetric fibre grating, the LP₁₁ mode is converted to the LP₂₁ mode with a spatially periodic force of 50 N along the fibre length of 50?mm. The mode conversion is evaluated by observing the far-field and near-field patterns of the fibre output and by comparing the transmitted optical power with and without the additional two-mode fibre. The phase-matching grating period is required of the accuracy of roughly ±5?μm and the radiation loss during the mode conversion is as low as 0.01?dB.     

应用变频器技术实现SO2风机节能改造

铜目前,硫酸车间制酸一系列共有三台SO2风机,这三台风机均采用液力耦合器的调速方式,这种方式可以实现无极调速,但是存在着传动效率低,耗能大的缺点,并且这三台风机均已使用20年以上,处于设备的中晚期,工作效率已大大降低。目前行业内,均采用先进的变频调速方式。使用变频器来控制风机的转速,可以极大的节省电能,尤其是在低负荷情况下,可以实现低转速运转,大大提高硫酸系统的综合能耗指标。     

煤油气共生矿井底板油型气赋存特征及防治

为了提高煤油气共生矿井油型气灾害治理的科学性，以黄陵二矿为例，采用现场测试、钻探取芯、跟踪观测、地质分析等多种方法，研究了采掘工作面煤层底板油型气分布特征、涌出规律和运移机理，并初步探讨了底板油型气体灾害防治措施。结果表明:底板油型气涌出点多位于底板砂岩储层上倾尖灭端和砂岩透镜体附近，呈现不连续区带状分布特征，涌出的油型气主要来自富县组砂岩层，涌出的动力主要为地层流体压力差，底板油型气通过地层中存在大量的断裂和裂缝、微裂缝系统进入采掘空间，采掘扰动是底板油型气异常涌出的工程诱导因素。建议加强油型气综合探查技术、油型气灾害预测预报技术、油型气综合抽采技术和智能化矿井建设等方面的研究。     

贾燕1,赵永涛2,张红松2

为确定ZrO2/莫来石热障涂层的单层最佳厚度,采用有限元技术研究单层厚度对ZrO2/莫来石热障涂层热冲击应力的影响。结果表明,莫来石层厚度为0.25mm时,涂层表面及ZrO2/莫来石界面处具有最大热应力,而其它莫来石层厚度时涂层内部热应力则受莫来石层厚度影响不明显。当ZrO2层厚度为0.3mm时,ZrO2/莫来石涂层中的热应力在整个横向距离范围内保持稳定,而其它情况下涂层中的热应力则与ZrO2层厚度成正比。涂层表面处的径向热应力大于ZrO2/莫来石界面处的对应值。     

利用表面硬度值间接获取镐形截齿钎焊层力学性能的方法研究

利用维氏硬度实验和数值模拟相结合的方法,间接得出了截齿表面各区域材料所对应的屈服强度值,建立了一种由实验硬度值HV获取截齿焊接接头等不易测量区域力学性能参数的方法。     

上保护层开采底板破坏深度和应力分析研究

上保护层开采导致的底板变形、应力释放会使被保护层内高瓦斯沿着上覆岩层内形成的空隙裂隙结构向上运移，很容易造成所采工作面采空区内瓦斯增加，造成工作面瓦斯超限。以峰峰集团以黄沙矿为研究实例，针对其主采的2号煤层利用FLAC^3D模拟软件进行上保护层开采底板应力研究，揭示了上保护层开采底板应力的规律特性，对于保护层开采工作瓦斯治理具有一定的指导意义。     

Effect of clad ratio on interfacial microstructure and properties of cladding billets via direct-chill casting process

Numerical simulation and experiments were introduced to develop AA4045/AA3003 cladding billets with different clad-ratios. The temperature fields, microstructures and mechanical properties near interface were investigated in detail. The results show that cladding billets with different clad-ratios were fabricated successfully. Si and Mn elements diffused across the bonding interface and formed diffusion layer. With the increase of clad-layer thickness, the interfacial region transforms from semisolid–solid state to liquid–solid state and the diffusion layer increased from 10 to 25 μm. The hardness at interface is higher than that of AA3003 side but lower than that of the other side. The bonding strength increased with the clad-layer thickness, attributing to solution strengthening due to elements diffusion. The cladding billets were extruded into clad pipe by indirect extrusion process after homogenization. The clad pipe remained the interfacial characteristics of as-cast cladding billet and the heredity of clad-ratio during deformation was testified.